What causes the P0013 code? Clean, replace, or repair connector as required. The list of automotive Makes at the right edge of the screen. Note the fine wire mesh screens on the bottom part. Then check for a lack of continuity in the solenoids themselves. With the repair manual and wiring diagram, you should be able to determine which wires to test and how to determine if the valve is electrically functional.
Refer to Oil Pressure Diagnosis and Testing. This causes the ignition coil to provide a spark and the injector to inject fuel into each cylinder at the right time. Determine that the vehicle has the correct engine oil. Check connector first for oil residue. Observe the engine oil level. Allow the engine to reach operating temperature. The test lamp should not illuminate.
If the circuit tests normal, replace the control module. Remember to refer to an appropriate manual for specific instructions. How does a mechanic diagnose the P0013 code? After some research I did some troubleshooting. We are not responsible for any actions you take on your vehicle. Pull over, retighten it, and take a look at the cap to see if it has any cracks in it. Thank you My car has 178000 miles.
Engine light started coming on so I took it to AutoZone and got it scanned. You must diagnose the circuit to find the cause. It could be that the solenoid itself has an open circuit in its coil windings, or it could even be caused by squirrels or mice chewing on the wiring harnesses in your engine compartment. Check Engine Light Code P0013 Exhaust Cam Position Actuator Open Circuit - Bank 1 Description: How does a P0013 code trigger the check engine light? Prices vary wildly depending on where you buy them, same with labor rates. If the voltage falls below a set limit for a specific amount of time during this test, the check engine light will come on and set this trouble code. P0013 code on vehicles with electronically controlled automatic transmissions, the 3-4 shift solenoid is responsible for actuating the hydraulic circuits to activate clutches or bands that change gears inside the automatic transmission.
It could be as simple as a loose connection at the solenoid electrical connector. How serious is the P0013 code? If the plug wires are out of sequence, the explosion occurs at the wrong time. This could be an electrical issue with the wiring to that solenoid itself. The engine oil level should be within the operating range. Now don't ask yourself; What should you do with P0013 code? In these cases, it is advisable to replace both the oil flow control solenoid, and the entire harness that controls it. The function of variable valve timing is to enable engines to develop more torque under different operating conditions.
Note: Follow the manufacturer's recommended pinpoint test to narrow down the problem, since each engine may be tested differently and possible engine internal damage may be done if tests are not performed in accordance with a correct procedure. There may also be a problem with a stretched camshaft timing chain or worn cam chain guides - especially if cam chain timing components have not been serviced on your engine. This code could also be set as the result of a performance failure in the system. In this case, if the cam timing is above a set limit over- advanced , the engine light will be illluminated and the code will be set. Then I started the car and the engine light was gone so I thought it was fixed.
What are the symptoms of code P0013? Since your problem comes and goes, I would check the wiring and connectors closely as a first priority. Justin- Year, Make, Model, Engine? Replace solenoid if resistance is out of spec. Next morning I started the car and the engine light was back on so I repeated the process and now the engine light is off. Look up the other , please use the search box. Bank 1 refers to the side of the engine that contains cylinder 1. In a properly timed engine, this explosion occurs at the proper moment to send the piston to the bottom of the cylinder and provide power to the drive shaft.
The information contained on this site is presented for informational purposes only. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation. What repairs can fix the P0013 code? The control module increases the pulse width to accomplish the desired camshaft operation. YourMechanic offers certified mobile mechanics who will come to your home or office to diagnose and repair your vehicle. Resistance should be between 8-12 ohms. The spool valve should move from fully closed to fully opened position.
I recommend a performed by a mobile, professional mechanic, such as one from YourMechanic, who will come to your location, diagnose this problem, give you an accurate assessment of damage and cost estimate for repairs. Note: The symptoms may change depending on the camshaft timing positions when the camshaft stopped advancing or retarding. The solution is here : P0013 Possible Solution: Gasoline engines use spark plugs to cause an explosion of fuel within the cylinder. The valve should be closed during idling, but higher engine speeds will activate it. Refer to Service and Appearance Care in the owner's manual. If the circuit tests normal, replace the control module. Retests the vehicle to see if the P0013 code comes back.
If you've already made it to the store, you might as well just replace it. The solution is here : Pontiac G6 P0013 Possible Solution : The crankshaft sensor signals the fuel injection computer or the ignition control when the cylinders are firing. The test lamp should illuminate. If the circuit tests normal, replace the control module. The test lamp should not illuminate.